iFlight Nazgul5 V2 Brushless FPV Drone (BNF / FrSky / 4S)

Regular price $289.99

Shipping calculated at checkout. See Shipping Policy for shipping times.

Nazgul5 V2 is a 5" sized FrSky Quadcopter. Pre-tuned and pre-setup, it's everything you need to bind and fly! Loads of power and smooth flights using iFlight's popular XING-E motors with long-lasting NSK bearings. 


Pre-Tuned and set up so you don't have to worry about a thing! iFlight did that for you already. A basic PID and Filter tuning was applied for a great flight experience! To restore lost tunes or updates, see the "Firmware/Factory Dumps" link below.


Angle-Mode (self-balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess! Please check the link below on "How to disable Angle-mode and activate Acro-Mode.



  • 5mm arm design for more durability
  • Easy-Swap arms
  • LED illuminated Logo
  • XING-E 2207 motors and NAZGUL 5140 props
  • 5" version also fits 5.1" style propellers
  • Popular True-X configuration
  • TPU crash-guards
  • Fits both 30.5x and 20x stacks




  • SucceX-E 45A 2-6S BLHeli_S 4-in-1 ESC
  • SucceX-E F7 V2.1 Flight Controller
  • XING-E 2207 FPV Motor (4S 2750KV)
  • Wheelbase: 240mm*240mm
  • Body size: 170*170mm
  • Propeller size: 5 inch /5.1 inch
  • FC pattern: 30.5*30.5/20*20 mm
  • FPV cam spacing: 19mm
  • Weight: 393.4g (without battery)

    Flight Controller:

    • FC // SucceX-E F7 Flight controller
    • MCU: STM32F22RET6 216MHz
    • Gyro: MPU6000
    • Baro: DSP310 (Barometer can only be used with Betaflight 4.3.0 and above)
    • OSD: IFLIGHT OSD (AT7456E)
    • BEC: 5V 2.5A
    • BlackBox: 16MB
    • Uart: 4*UART(UART1、UART2、UART4、UART5)
    • UART1 for VTX HD(for 4-6S Vista,for 4S DJI Air Unit)/AnalogTelemetry
    • UART2 for Receiver
    • UART4 for Free
    • UART5 for ESC Telemetry
    • 4×Dshot/PWM outputs
    • Smartaudio & IRC Tramp VTX protocol supported
    • WS2812 led Strip: Yes
    • Beeper: Yes
    • Firmware: IFLIGHT_SUCCEX_E_F7
    • Outer Size: 36*36mm / 30.5*30.5/φ4 mounting
    • Weight: 6.9g



    • ESC // SucceX-E 45A 2-6S BLHeli_S 4-in-1 ESC
    • Dimension: 36*43mm
    • Mounting Holes: 30.5*30.5mm/Φ3mm
    • Weight: 15g (without wire)
    • Supports 2-6S Lipo input
    • EFM8BB21 MCU, 24Mhz Runs BLHeli_S 16.X Firmware
    • Current sensor: YES
    • BEC: NO
    • Constant: 45A / Burst: 50A
    • Supports: DShot150/300/600/MultiShot/OneShot etc.
    • Target: G-H-30 BLS 16.7



      • SucceX Force
      • Stable output power
      • Transmit power 4 gear switch: 25mW/200mW/400mW/800mW
      • Output 48 frequency points
      • Frequency lock fast, the boot does not interfere with companions
      • Built-in output power self-check function
      • Full format video format: NTSC /PAL
      • Wide input voltage range: 7V~36V
      • Low power consumption: +12V/380mA@800mW
      • Small size: 36 x 36 x 3mm
      • Mounting holes: 4-M3
      • Lightweight: 0.25oz (7.2g) (excluding antenna)



      Firmware/Factory Dumps

      Switching from Angle to Acro Mode



      (1) iFlight Nazgul5 V2 Brushless FPV Drone w/ XM+ v2.1
      (1) RaceCam R1 Mini 1200TVL 2.1mm 19*19
      (1) Albatross RHCP SMA 5.8g Antenna
      (2) Sets x Nazgul 5 inch 3-blades (Set of 4 - Color may vary)
      (1) 20*200mm Microfiber PU Leather Battery Strap (Color May Vary)
      (1) 20*250mm Microfiber PU Leather Battery Strap (Color May Vary)


      • The Frsky xm+ & RXSR receivers installed on this drone will only bind with the latest Frsky module protocol 2.1 version. If your transmitter or module doesn't have the latest Frsky version, you will have to downgrade this receiver's firmware. We can perform this service for a $10 fee per device.



      Sold Out