SpeedyBee F7 V3 Flight Controller (30x30 / 5 Uarts / 3-6S)

The SpeedyBee F7 V3 Flight Controller is a feature-packed F722 FC designed for FPV drones. It offers wireless configuration, Blackbox data access, plug-and-play connectivity, motor direction configuration, X8 Cinelifter support, an LED battery indicator, and massive Blackbox flash memory. If you’re looking for a flagship stack that combines performance, convenience, and affordability, the SpeedyBee F7 V3 is an excellent choice!

SPECIFICATIONS:

• Input Voltage: 3-6S LiPo
• Power Output:
  1) 10 groups of 5V output, three +5V pads and 1 BZ+ pad (used for Buzzer) on the front side, and 6 +5V output included in the connectors on the bottom side. The total current load is 2A.
  2) 2 groups of 9V output, one +9V pad on the front side and the other included in a connector on the bottom side. The total current load is 4A.
  3) Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load Supported. Designed for 3.3V-input receivers. Up to 500mA current load.
  
• WiFi Support: Used for data transfer, e.g firmware flashing, and Blackbox analysis.
  
• I2C: Supported. SDA & SCL pads on the front side. Used for magnetometer, sonar, etc.
  
• Support Flight Controller Firmware: BetaFlight(Default), EMUFlight, INAV
  
• ESC signal M1 - M4 on the bottom side and M5-M8 on the front side.
  
• LED: Used for WS2812 LED controlled by Betaflight firmware.
  
• UART: 5 sets (UART1, UART2, UART3, UART4, UART6)
  
• DJI Air Unit plug: A full DJI Air Unit JST slot onboard
  
• BLE Support: Used for Flight Controller configuration
  
• Buzzer: BZ+ and BZ- pad used for 5V Buzzer
  
• Mounting: 30.5x30.5mm, 4mm hole size
  
• Dimensions: 41(L) x 38(W) x 8.1(H)mm
  
• OSD: BetaFlight OSD w/ AT7456E chip
  
• BlackBox: 500MB onboard data flash
  
• BetaFlight Camera Control Pad: Yes
  
• ESC Telemetry: UART UART4 RX
  
• Target: SPEEDYBEEF7V3
  
• SmartPort: Supported
  
• Baro: BMP280 (I2C)
  
• MCU: STM32F722
  
• Boot button: Yes
  
• RSSI input: Yes
  
• IMU: BMI270
  
• USB: Type-C
  
• Weight: 9G

HELPFUL LINKS:

• Manual
• Wire Diagram

INCLUDES:

(1) SpeedyBee F7 V3 Flight Controller
(1) 4-Pin SH1.0 to SH1.0 Analog VTX Cable 60mm - Yellow and Blue
(1) 6-Pin SH1.0 GPS module Cable without connector - 100mm
(1) 4-Pin SH1.0 to 3+ 2-Pin JST1.25 FPV Camera Cable - 30mm
(1) 4-Pin SH1.0 to 3+ 2-Pin JST1.25 FPV Camera Cable - 60mm
(1) 4-Pin SH1.0 to 4-Pin JST1.25 FPV Camera Cable - 60mm
(1) 6-Pin SH1.0 GPS module Cable with connector
(1) 4-Pin SH1.0 Radio Receiver Cable - 100mm
(1) SH 1.0mm 8-Pin Cable -30mm
(5) M3 8mm Silicone Grommets
(1) DJI 6-Pin Cable - 80mm

NOTES: 

• Manufacturer upgrades, alterations, and processor/firmware changes are frequently made without prior notice. Exact specifications, photos, and links cannot be guaranteed.